Water Bath For Developing Film At Home – C41 E6 B&W

Here is a quick video, some pictures, and a parts list for my over engineered water bath. I will use this water bath for processing color film where maintaining temperature is critical for success. Of course, it could be used for processing B&W film too.

Note: This is by no means a detailed how-to/tutorial. It’s just a video, some pictures, and a list of parts that I used to make it. Hopefully it will give you some ideas for making your own water bath.

Video

Parts List

-Water Tank – I had my stainless steel tank already. You could search ebay for something that might work, or maybe you can find something at your local hardware.

PID Temperature Controller, Thermocouple, SSR (Solid State Relay) – I didn’t use the Thermocouple (Temperature Sensor) that came with this kit. The thermocouple is not water tight. I could have sealed it up with a bunch of sealant, but that’s not my style. I purchased the liquid tight RTD sensor below instead. You may be able to find this PID for cheaper if you purchase just the PID without the Thermocouple. You’ll need to purchase the SSR (Solid State Relay) separately as well though, so it may be a wash.

120 GPH Submersible Aquarium Pump – (Qty: 2) – The pumps circulate the water in the tank. You can probably get away with one pump, but I like two. It will depend on the size of your water bath tank too. The video shows only one pump.

Liquid tight RTD sensor, 2 in, 1/4 NPT Thread (Deluxe Cable) – This is the sensor that monitors the temperature of the water in the tank.

1000 Watt Heater Element
Power Inlet
Die Cast Aluminum Enclosure
External Mount Heat Sink for 25A SSR
Brass Pipe Fitting, Locknut, 1/4″
Brass Pipe Fitting, Locknut, 1″

Red 15A Single Round Outlet Receptacle – The red outlet is controlled by the PID controller and turns on/off based on the water temperature. It’s what I plug the heater element (yellow cord) into. You don’t have to use a red receptacle. I just thought it was cool.

Hubbell AC Receptacle 15A/125 vac – (CNE) HBL5261D
1 Gang Weatherproof Electrical Outlet Box
-2 A/C Neon Indicator Lights (1 Red, 1 Green)
-A/C On/Off Toggle Switch
-An old yellow extension cord I had laying around
-A power cord from an old computer to power the controller/system.

Pictures

01

01a

02

03

04

05

02b

02a

10

08

11

17

07

21b

21a

22

13

14

18

19

20

15

16

12

21

23

7 thoughts on “Water Bath For Developing Film At Home – C41 E6 B&W

    1. Wolfy Post author

      Hi Ron. Sorry for the long delay. Extremely long delay! I already had it. I would search ebay or Craig’s List for stainless steel tank, or sink, etc.

      Reply
    1. Wolfy Post author

      Hi Geo. Sorry for taking so long to reply. Unfortunately I didn’t make a wiring diagram of the project. I should have. It was pretty basic wiring though.

      Reply
    1. Wolfy Post author

      Thanks Brian. You are correct, it’s stainless steel. I would search ebay or Craig’s List for stainless steel tank, or sink, etc.

      Reply
  1. R.

    Hi.

    I have started to pickup info for building my own water controlled bath for C-41 (DIY is half the fun…).

    Depending on the chimistry, C-41 needs 38°C +/- 0,5°C. There no place for approximation. What kind of precision can you get with your PID controller?

    With your PID, do you control the “hysteresis” for better precision? Or is the auto-tune mode good enough to get this +/- 0,5°C precision ?

    In other words, I just don’t know which PID controller tu buy. Are they all alike? Or should I watch for a model with auto-tuning?

    Thanks for your input on this.

    R.

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *